 |
 |
|
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
|
YOU ARE HERE: Home  Franz Cells Franz Cell Photos |
 |
|
|
|
 |
|
|
|
|
|
|
Franz Cell & Accessories Photos and Information |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
The 9mm jacketed Franz Cell with the flat ground joint and clear glass pictured to the left is by far the most common variety in use today. When you order any standard Franz Cell you receive: a donor chamber, a receptor chamber with sampling port, a stirbar which is not pictured, and a clamp. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
The amberized cell shown to the left is a 20mm Franz Cell with a flat flange joint. It uses a horseshoe clamp that is tightened by turning the threaded thumbnuts. Long screws are available for these clamps in all cell sizes for clamping thick devices between the donor and receptor chambers. One researcher uses devices 30mm in thickness with flat flange joints. Even with a relative small orifice diameter of 9mm you can still clamp thick devices. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Type 3 Flow Cells like the 15mm cell shown in the photo to the left have flow ports but no separate manual sampling port. The flow ports are made of 6mmOD glass tubing and enter the bottom and top of the receptor chamber. Either one may be used as a manual sampling port and if the user desires, fittings may be provided on the ends of the ports to seal them. Female luer fittings are most commonly ordered for this purpose. The receptor chamber in this cell is smaller in diameter than normal for a 15mm Franz Cell. The user wished to have the receptor chamber volume to be as small as possible given the standard height of PermeGear Franz Cells. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
The 20mm Franz Cell in the photos has a flat ground joint with a pinch clamp, flow porting and a 14/20 ground joint in the donor chamber. A donor chamber with flow porting may be used to deliver or draw off gases to or from the donor chamber. These ports may also have female luer joints so with stoppers in them, the donor chamber may be used in a static fashion. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
The Franz Cell shown in the photo to the left has a standard 11.28mm diameter jacketed body with a flat ground joint, but the donor chamber has a female luer fitting on the top so the user can attach a syringe to it. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Both of the cells shown in the photo to the left are 11.28mm orifice unjacketed Franz Cells with flat flange joints. Only the bodies of the cells are shown, there are no donor chambers.The small cell has a 2ml receptor volume, the larger cell has a 4ml receptor volume. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
The cell to the left, like the cells shown above, is also an unjacketed Franz cell. It has a 5mm orifice diameter but the user wanted a relatively large 20ml receptor chamber volume and a flat ground joint. |
|
|
|
|
|
|
|
|
|
|
|
 |
|
|
|
|
PermeGear, Inc. | |
1815 Leithsville Road | |
Hellertown, PA 18055 USA | |
Tel 484-851-3688 | |
Fax 484-851-3668 | |
| CONTACT | Copyright ©2005 PermeGear, Inc. |
Please excuse us while our site is under construction!